Top 10 typical forklift mishaps ， forklift procedure must focus on these matters ！.

Top 10 typical forklift mishaps ， forklift procedure must focus on these matters ！.

Blog Article

Do not ignore the forklift at the office. If the procedure is not good, there will be serious mishaps in minutes, and there are several mishaps including forklifts.

Case 1: The forklift cargo obstructed the motorist's view, and the person ahead can not be discovered, causing a rolling mishap.
Case 2: In order to preserve the equilibrium of the forklift when raising heavy goods, the employees used their body weight as the counterweight, which virtually caused casualties.
Instance 3: The width of the forklift freight goes beyond the allowed size of the path and hangs on the roadside shelf, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift raises the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur needs to first validate that the load is secure and reputable.
4. The start needs to be slow-moving and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released first. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral security and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the flame and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are special conditions.
6. When the forklift is running, it has to obey the traffic rules in the factory and should keep a specific security distance from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be increased except when stacking or loading. .
8. The height of the lots have to not obstruct the vehicle driver's view. In special situations, when the product affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive securely at a reduced speed when entering the production workshop location. .
11. When the forklift is lifted, lifted or driven, it is forbidden for employees to base on the fork to hold products and play a balancing duty. .
12. If problems are located, they will certainly be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

filling and discharging.
1. When fork-loading products, the distance in between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to collaborate with a solitary fork or use a fork top or draw. In special conditions, security indication need to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it needs to be noted that the fork idea should not touch various other items or objects. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to permit very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is forbidden to make use of forks to raise employees to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, put, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage ought to also be examined Stand-on Electric Pallet Stacker and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no activating the slope is permitted.
7. Do not Electric Forklift Truck for Warehouse drive across the slope. When the gradient is greater than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy products and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844